Color: Blue and grey
INQUIRE ABOUT TO SEE IF YOU QUALIFY FOR FREE SHIPPING!!! The CAMFive CFL-CMA 6040 industrial laser cutter and engraver machine is specially designed to work 24/7. This machine is equipped with one honeycomb work table 24"x16" (Stripped work table also available); One laser pen, air assist and red dot pointer to trace a simulation of your design before you send the laser; One CO2 80 watts RC long life laser tube, up to 10,000 hours; a fume extractor; One air compressors; a water cooling system for the tube and the lenses and sensors in the doors that make the laser stop if somebody opens the doors by accident.
Kerr Lab Large Automatic Maxi Electro-MeltTM Largest capacity hand melter. Features an electronic controller with digital display, which will hold the temperature you set to within Â± 5Â°F. Most importantly, the electronics are designed to eliminate temperature overshoot. Also features a bright LED digital readout in Â°F or Â°C. Comes complete with a graphite crucible (which provides a reducing atmosphere during melting), 12" carbon stirring rod and safety switch. Hand held compact electric furnace for melting metals. Digitally controlled, recommended when sustained high temperature use is required. Electronic controller regulates the temperature by providing full power input until a pre-selected temperature is attained. Features Melting capacity: Gold - 3.1 kg/100 Troy oz Silver - 2.6 kg/83 Troy oz Maximum temperature 1120Â°C / 2050Â°F 31 minutes to 982Â°C/1800Â°F CE, UL & CUL Certified
Orion Motor Tech 12"x 8" 40W CO2 Laser Engraving Machine Engraver Cutter with Exhaust Fan USB Port
Manufacturer: Orion Motor Tech
K40-3020 Laser: 1. This engraver is compatible with CorelDraw , but CorelDraw is NOT included.Compatible with corelaser (which requires CorelDraw) and laser DRW (compatible with most graphic design programs) 2. Make sure the JPG pictures are of high resolution if you're to use JPG pictures, otherwise the patterns to be engraved might be vague. 3. Use vector grams done by CorelDraw to engrave for ultimate results. 4. The quality of patterns to be engraved depends on a lot of factors: engraving speed, laser power, current amperage etc., all of which should be set correctly according to the manual provided. 5. Rotary device is NOT included, and cannot be added to this engraver. 6. This 40W engraver can be updated to 50W as long as you change the laser tube and the power supply. Package includes: 1 CO2 Laser Engraver 1 Air Exhaust Fan 1 Venting Tube 1 Water Pump 1 USB Key & USB Cable 1 Software 1 Manual Specifications: Suitable materials: wood, stone, glass, leather, crystal, paper, film, rubber, bamboo, and many other non-metal materials (This machine will not work on any metals. It can only mark on the anodized coating / non-metal surfaces). Engraving area: 12" x 8" / 300 x 200mm Laser power: CO2 Glass 40W rated an estimated 1,000-1,300 hoursCompatible operating systems: Windows 2000, XP, 7, 10 and 8(32/64 bit); NOT compatible with iOS systemSoftware interface: Shenzhouyi / Laser Draw Software / Core Draw Software Resolution: Up to 1000 dpiMotor type: Stepper Motor Power supply: AC 110V Working temperature: 40 - 104Â°FWorking humidity: 5% - 95% without condensed steamMachine dimensions: 31.5" x 19.5" x 10" Product Weight: 67 lbs Package Weight: 80 lbs
This CO2 laser engraver is equipped with one 40W water cooling laser tube, high precise stepping motors. It is suitable for various materials, such as bamboo piece, double-color planks,boulder,horns,leather,crystal, wood,organic plastic,abrics, paper, Acrylic and Plastics.
Interface to Computer: USB Port
Tube Trigger Volt: 20KV;Tube Operating Volt: 15KV
Engraving Area: 260x180mm
Maximum Item Size to Engrave: 10.25W x 8.75L x 2.85H in (260mm x 220mm x 70mm)
Laser Tube (life hours): 1000-1300 Hours
Laser Power: 40W
Engraving Speed: 0-13.8 in./s (0-350mm/s)
Cutting Speed: 0-1.38 in./s (0-35mm/s)
Minimum Shaping Character: 0.04X0.04in (1mm X 1mm)
Resolution Ratio: 0.001 in (0.026mm) / (1000dpi)
Resetting Positioning: 0.0004 in (0.01mm)
Software Supported: MoshiDRAW software (both NewlyDraw and NewSeal function)
Power Consumption: 250W
Operating Temperature: 32-113F (0-45C)
Recommended Spare Parts/Consumables: Laser Tube, Focal lens, Reflection lens
Adopt Germany imported bearing and high accuracy stepping belt.
Adopt Japan imported mainboard and chip which can control the engraving more precise.
Built the heat dispersed fan to reduce all electronic component's temperature.
The Gold Cube can can process tons of concentrates into mere ounces. With a 12-volt battery (not included) you're ready to clean up your concentrates QUICKLY! The Gold Cube is small and consists of stacking trays made of indestructible plastic LDPE (low density polyethylene) that's as thick as a cutting board. The slick plate on the Gold Cube has a precisely controlled water flow that is designed to process very large amounts of 8 mesh and smaller material in a very short time. With controlled water flow, the slick plate turns aggregate material into a slurry, and the water flow forces the lighter particles ahead of the heavier material. It is quite exciting to actually see your fine gold creeping down the slick plate! Gold, the heaviest element in the slurry, will be the last to reach the trough. G-Force Separator. The slurry then falls into a gated trough and will be forced under water. Then centrifugal force will force the gold to the outer edge of the rounded trough. The slurry will then exit the trough on the opposite side of the gate. After exiting the gated trough, the slurry is forced to stand up and form a column. The purpose of this column is to actively stack the particles by specific gravity. Lighter, faster moving particles race past the heavier particles and exit the column first. The Gold Cube's forced gravitational, centrifugal and columning effect is called "the G-Force." The Gold Cube's vortex matting works because water flow interacts with a combination of very small pillar walls and cavities-about 7,056 of them per mat. Just like a tornado, the spinning creates a low pressure zone in the center of each cavity. Passing gold will be trapped and forced to the bottom of the vortexes and held in place by the lighter material. As gold-laden material is introduced into each vortex mat, it will displace and replace the lighter material. This will create about a cup of super concentrates at clean-up. Amazing!
40w Laser Engraver Engraving Machine 300x200mm Woodworking USB Port Description: This brand new DC-KIII CO2 laser engraver is equipped with one 40W water cooling laser tube, high precise stepping motors, high quality control board. It employs an USB port and thus can be connected to your laptop or desktop. By the support of included software, Coreldraw, this machine can work well with multiple graphic formats including EMF/JPG/PLT/WMF. Specifications: Engraving Area: 300 x 200mm Laser Power: CO2 Glass 40W rated an estimated 1,000-1,300 hours (cuts up to 3mm wood / acrylic) Material Capability: Organics / non-metal - can mark on treated metals: wood, stone, leather, crystal, paper, and film Vent Attachments: Air Exhaust fan w/ vent pipe Power Supply: Standard AC 110V Laser / PC Connectivity: USB Resolution: Up to 1000 dpi Interface to Computer: USB Port Laser Type:CO2 Gas Current:0~22mA Maximum Item Size to Engrave: 260*220 *70mm Laser Tube:1000-1300 Hours Laser Power:40W Minimum Shaping Character:0.04 X0.04in (1mm X 1mm) Resolution Ratio:0.001 in (0.026mm) / (1000dpi) Resetting Positioning:â‰¤0.0004 in (0.01mm) Motor Type:Stepper Motor Software Supported: CorelDrawÂ software Power Consumption:â‰¤250W Operating Temperature:32-113F Water Cooling:Water Pump include Recommended Spare Parts/Consumables:Laser Tube, Focal lens,Reflection lens Package List: 1 x CO2 LASER Engraver 1 x Smoke Pipe 1 x Smoke Fan 1 x Water Pump 1 x Power Wire 1 x USB Cable 1 x USB Key 1 x Accessory Bag 1 x Instruction Video 1 x English User Manual
Presidium Adamas Diamond/Moissanite Tester Package with Additional Regular Size Replaceable Tip & USB Charger
Color: Black and Silver
Presidium presents Adamas- the epitome of cutting-edge technology. With a revolutionary replaceable probe tip that minimizes equipment downtime, Adamas also has a micro probe tip that is the first in the world to measure diamond melees as small as 0.01 carats. A hallmark of dedicated design featuring a dynamic LED display and a sleek ergonomic grip, Adamas reaches new heights and presents new possibilities with the precision, quality and reliability long associated with Presidium products. Adamas offers a revolutionary diamond testing experience. It allows users to replace the probe tip at any time, without the inconvenience of returning the device to the manufacturer whenever the probe tip gets damaged - whether it is bent or broken. The usual scenario of incurring freight charges and 2-3 weeks of downtime no longer applies with Adamas. Users can simply replace the probe tip and do a calibration of the device at any time, to ensure its accuracy. Adamas also presents the world's first micro tip with an enhanced and refined probe tip of just 0.45mm to measure diamonds and diamond melees as small as 0.01ct. The micro tip comes as an optional accessory with Adamas. Created with the user in mind, Adamas features a stylish ergonomic design, which provides a 360Â° textured chrome grip as well as a balanced weight throughout the tool so as to increase your handling comfort. Adamas has been subjected to thorough and extensive laboratory tests, and gives a clear and reliable reading of the gemstone when tested under proper use. This special upgraded package includes the Presidium Adamas tester, an additional Regular Replacement Tip as well as a 100-240V USB charger.
WER 1000mW USB DIY Laser Engraver Printer Mini Art Craft Science Industry Laser Engraving Cutting Machine
WER TECHNOLOGY 3d printer WER I is the most precise and dependable 3d printer.Each 3d printer is leveled, fully calibrated and operated 8 hour before delivery. QIDI TECH after-sales team supplies technical support and lifetime service. Specification Brand: WER Model: DK-8-KZ Color: Black & Red Material: Acrylic + Aluminum + Stainless Steel Laser Power: 1000mw Laser wavelength: 405nm Laser Operating temperature: 500 degrees Support software: Laser Carver Image formats: jpg Image Size: 512x512 pixels Image engraving pattern: Bitmap engraving Power mode: Dual USB powered Supply voltage: 4.2V-5.5V Supply Current: 1A Support xp, win7, win8, win10 Can be carved objects: mahogany, bamboo, paper cards, ivory, leather, flammable plastic, PCBA, etc and so on. Can NOT engrave Metal/Aluminum/Acrylic. Uses: engraving, hand tools and industrial processing High power, high speed, high precision Work Area: 38*38mm What size image can it print up to, what thickness of items can be printed on? 38*38mm Size: 19x14.5x16cm Net weight: 970g Package size: 30*21*20cm Package Weight: 1400g Free software download: http://www.trusfer.com/#Download.IMPORTANT NOTE:You might need to temporarily shut down the antivirus software before downloading the software. Otherwise some files in the software would be mistaken for virus and deleted by antivirus software. We hope for your understanding. Package List: - 1 x Engraving Machine - 1 x Laser Protective Glasses - 1 x Allen wrench - 2 x USB Cables - 1 x FREE 1Gb TF Card ( Included the User's manual and install software )